4: Sewing with difficult fabric

There comes a time when we all would like to use something a little more adventurous and preparing the Fabric well is half the task of sewing Lace, or Sequinned Fabric, which are popular choices for Corsetry.

Lace Overlays

When using Lace for Corsets, you will need to consider the pattern of the Lace- is it large or small and do you need to take this into consideration when placing the Pattern Pieces? You will need to re-trace off your Corset Pattern (from your adapted Pattern) and add in Seam Allowance before cutting out. This will ensure you do not have to draw the Seam Allowance on to the Lace which can be difficult for a number of reasons- the Lace will move about and can stretch out of shape, it will also be delicate and should not be overly handled.

After tracing the Paper Pattern off, pin the Paper Pattern on and cut out as you would Fabric. If the lace is very delicate, you may wish to use Pattern Weights instead of Pins to ensure you do not damage the Lace. I do not worry about being overly accurate- as long as the Lace is cut out within 1cm of the edge of the Paper Pattern and all Waist Notches are marked you will be fine.

Once all Lace sections are cut out, lay the Fabric pieces of the Corset out, then lay the Lace sections on top. Double check your Waist Notches are all in line throughout the Corset pieces, and that you have a left and a right of each piece.

sequin 1
sequin 2

Pin the layers together, pin carefully so as to not damage the Lace.

Tack each section together as illustrated. Use a contrast Tacking Thread, and try to keep within the 1.5cm Seam Allowance so you will not have to remove it. If, when the Corset is sewn up, you can see the Tacking Stitches, the contrast thread will help you to see where to remove them.

Once the pieces are tacked, you can trim back any excess Lace to the edge of the Fabric.

sequin 3
sequin 4

Alternatively, and you may wish to Sew a couple Corsets having tacked them before trying this method!- you can pin the sections together as illustrated. Pin along the Seam Allowance as shown, and keep the Pins in until they are stitched up. Of course, whilst this method is quicker there are some obvious drawbacks! If you have to adjust the Corset or unpick it for any reason, these pieces will become separated and need to be pinned again, it will take a little more experience to be able to control the layers of fabric with just pins holding them together… you also use a lot of pins!!

sequin 5

This is a technique I often use when manufacturing multiple Corsets.

Sequinned and Beaded Fabrics

Sewing with Sequinned and Beaded fabrics has another set of rules. Because you are unable to Sew over Beads or heavier weight Sequins, you will need to remove them from the Seam Allowance.

It is easiest to trace off the Pattern, and add the Seam Allowance as for working with Lace Fabrics before pinning in the Pattern and cutting out.

Using a Tape Measure, measure in 1.5cm (which is the Seam Allowance for the Eventide Corset Pattern) and mark with a line of Pins as illustrated.

beaded 1
beaded 2

With a contrast Thread, tack along the line of Pins.

beaded 3
beaded 4

When you have tacked a line of stitching 1.5cm in, you will need to remove all of the Beads and Sequins from the Seam Allowance. And yes, this takes ages!! I keep the Beads and Sequins I remove, in case I need to add a couple in again. The stitching which holds on the Beads or Sequins is actually a chain so sometimes a couple of centimetres can unravel when it is cut, and will need to be carefully sewn back down, or added in by hand.

I will insert the Busk by hand if I am making a Corset from Beaded Fabric so as to not disturb the pattern of the Beading at the front of the Corset.

Pattern Matching and using Patterned Fabrics

This tip for Pattern Matching Fabrics is enormously helpful however; if you are using a Patterned Fabric you may wish to select the sections you wish to use, or even Pattern Match the Front Panels so that the Pattern runs across them. This isn’t too difficult BUT please do try to remember to cut out a LEFT and a RIGHT of each Panel!! For this you will need to flip the Pattern Piece over.

pattern match

As illustrated above, I have chosen which piece of the Pattern I would like to run down the front of the Corset. Folding the Pattern Piece back along the Centre Front line, I have matched it so that- when the Corset is sewn together- the Cyclist will pedal across the Bust!

Remember to fold the Pattern Back along the Centre Front line, then match on the Fabric. As you Pin the Pattern Piece on to the Fabric you can un-fold it and pin it down.

Matching along the Centre Front line is incredibly important because- and you’ll see this from the Instruction Book– the Fabric beyond the Centre Front is used as a Seam Allowance when inserting the Busk, so any pattern will be lost.

Don’t forget, the Eventide Corset Pattern is available in a number of options including Instant Download here, and you the other posts in the Eventide Sew-a-Long here.

Happy stitching!

Leave a Reply

Your email address will not be published. Required fields are marked *